大家都来看看我虚拟机出现的问题吧，郁闷！！！高分求助！
我刚装的这个虚拟机VMware_6.5.3_HA_XiaZaiBa！装完之后打开虚拟机程序，我就新建了个虚拟机，新建虚拟机弄好之后我就接通虚拟机的电源，结果就出现了这个报错信息！赐教！
第1个回答 2013-09-07
你下载的这个版本可能有问题，我用的是VMware-workstation-6.5.3-185404_XiaZAiBa这个版的，没问题，不行，你下个这个安装
第2个回答 2013-09-07
报的错应该是找不到CPU吧！你找一个其它的ISO再重新安装一下看看！是否还会出现这样儿的情况呢！
第3个回答 2013-09-07
系统是35位的还是64位的？
第4个回答 2013-09-07
解决方法如下：
1、用process explorer杀掉vmware-vmx.exe进程（如果有的话）
2、清除虚拟机目录下的.lck文件
3、在dos命令行下执行net start vmx86，以启动peer process
2、VMware Tools问题 在vmware下安装完了后默认的分辨率选项只有800×600与640×480，在linux的"显示设置"里怎么修改显卡及分辨率后重新启动或注销都没有变化，要想改变linux的分辨率，必须安装VMware Tools；另外安装VMware Tools后提供了增强GuestOS的显示和鼠标功能，可以在虚拟机和主机之间流畅使用鼠标，不用通过CTRL+ALT切换
具体过程如下：
启动虚拟机 安装VMware tools 按照正常的方法安装VMware tools：VM -> Install VMware Tools。但是在点击InstallVMware Tools后安装后一段时间，没有任何反映，菜单项始终是“Cancel VMware ToolsInstall”,在tmp下也没有vmware-linux-tools.tar.gz。
实际上vmware-linux-tools.tar.gz保存在“VMware的安装目录\VMwareWorkstation\linux.iso”中，因此可以手工把vmware-linux-tools.tar.gz通过ssh或ftp上传到到Linux中安装即可。
也可以通过VMware 中mount cdrom的方法进行安装，步骤如下
在VMWARE菜单项VM ->Settings->CD-ROM(IDE 1:0)，指定“Use ISO image”，路径指向“VMware的安装目录\VMware Workstation\linux.iso”，如下图所示
init 3，切换到runlevel 3 mount -t iso9660 /dev/cdrom /mnt cd /mnt;ls /mnt 可以看到下面有如下两个文件VMwareTools-6.0.0-45731.i386.rpm VMwareTools-6.0.0-45731.tar.gz
安装VMwareTools 采用rpm包安装：
rpm -ivh VMwareTools-6.0.0-45731.i386.rpm
vmware-config-tools.pl
一路回车，完成后出现分辨率列表供选择
或者采用tar包安装：
cp VMwareTools-6.0.0-45731.tar.gz /tmp;
tar zxvf VMwareTools-6.0.0-45731.tar.gz;
cd VMwareTools-6.0.0-45731.tar.gz;
./vmware-install.pl
umount /dev/cdrom init 5 安装完成后，如有问题，可以通过执行/usr/bin/vmware-config-tools.pl 来运行vmware tools，重新配置vmware tool及设定系统分辨率等。
运行vmware tools后,X11的配置文件/etc/X11/xorg.conf内容为：
# Xorg configuration created by system-config-display
Section "ServerLayout"
Identifier "single head configuration"
Screen 0 "Screen0" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "XWorkAround"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
Option "XkbModel" "pc105"
Option "XkbLayout" "us"
EndSection
Section "Device"
Identifier "VMware SVGA"
Driver "vmware"
EndSection
Section "Screen"
Identifier "Screen0"
Device "VMware SVGA"
Monitor "vmware"
# Don't specify DefaultColorDepth unless you know what you're
# doing. It will override the driver's preferences which can
# cause the X server not to run if the host doesn't support the
# depth.
Subsection "Display"
# VGA mode: better left untouched
Depth 4
Modes "640x480"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 8
Modes "1024x768"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 15
Modes "1024x768"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 16
Modes "1024x768"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 24
Modes "1024x768"
ViewPort 0 0
EndSubsection
EndSection
Section "Monitor"
Identifier "vmware"
VendorName "VMware, Inc"
HorizSync 1-10000
VertRefresh 1-10000
EndSection
Section "InputDevice"
Identifier "XWorkAround"
Driver "void"
EndSection3、Bridge模式下vmnet0问题采用VMWare安装Rehat AS 5时候，采用Bridge模式，启动时候报错：
The network bridge on device VMnet0 is not running. The virtualmachine will not be able to communicate with the host or with othermachines on your network. Virtual device Ethernet0 will startdisconnected
原因是在宿主机的本地连接里少了：VMware Bridge Protocol,在正常安装后会在本地网卡的连接属性里有这一项的。
解决方法如下：
1、禁用vmnet1（host-only模式）和vmnet8(nat模式)网卡
2、在服务中禁用VMware NAT Service
3、安装VMware Bridge Protocol
控制面板->网络连接->本地连接->属性->安装->（选中服务）添加->从磁盘安装->浏览->
VMware安装路径\VMware Workstation目录下选 netbridge.inf
然后重装电脑。
4、VMware Tools在xeno服务器安装问题在DELL Powerdege 1900 服务器（xeon Processor）上安装的虚拟机，运行/usr/bin/vmware-config-tools.pl时候报错：
[root@linux-server-v1 ~]# vmware-config-tools.pl
It looks like you are trying to run this program in a remote session. This
program will temporarily shut down your network connection, so you should only
run it from a local console session. Are you SURE you want to continue?
[no] yes
Stopping VMware Tools services in the virtual machine:
Guest operating system daemon: [ OK ]
Trying to find a suitable vmmemctl module for your running kernel.
None of the pre-built vmmemctl modules for VMware Tools is suitable for your
running kernel. Do you want this program to try to build the vmmemctl module
for your system (you need to have a C compiler installed on your system)?
[yes]
Using compiler "/usr/bin/gcc". Use environment variable CC to override.
What is the location of the directory of C header files that match your running
kernel? [/usr/src/linux/include]
The path "/usr/src/linux/include" is not an existing directory.
找不到kernel的header文件，主要原因是没有安装kernel-xen-devel-2.6.18-8.el5，解决方案
确认安装了如下几个包，如果没有安装，从安装盘上拷贝安装上：
kernel-xen-2.6.18-8.el5
kernel-devel-2.6.18-8.el5
kernel-headers-2.6.18-8.el5
kernel-xen-devel-2.6.18-8.el5
1、用process explorer杀掉vmware-vmx.exe进程（如果有的话）
2、清除虚拟机目录下的.lck文件
3、在dos命令行下执行net start vmx86，以启动peer process
2、VMware Tools问题 在vmware下安装完了后默认的分辨率选项只有800×600与640×480，在linux的"显示设置"里怎么修改显卡及分辨率后重新启动或注销都没有变化，要想改变linux的分辨率，必须安装VMware Tools；另外安装VMware Tools后提供了增强GuestOS的显示和鼠标功能，可以在虚拟机和主机之间流畅使用鼠标，不用通过CTRL+ALT切换
具体过程如下：
启动虚拟机 安装VMware tools 按照正常的方法安装VMware tools：VM -> Install VMware Tools。但是在点击InstallVMware Tools后安装后一段时间，没有任何反映，菜单项始终是“Cancel VMware ToolsInstall”,在tmp下也没有vmware-linux-tools.tar.gz。
实际上vmware-linux-tools.tar.gz保存在“VMware的安装目录\VMwareWorkstation\linux.iso”中，因此可以手工把vmware-linux-tools.tar.gz通过ssh或ftp上传到到Linux中安装即可。
也可以通过VMware 中mount cdrom的方法进行安装，步骤如下
在VMWARE菜单项VM ->Settings->CD-ROM(IDE 1:0)，指定“Use ISO image”，路径指向“VMware的安装目录\VMware Workstation\linux.iso”，如下图所示
init 3，切换到runlevel 3 mount -t iso9660 /dev/cdrom /mnt cd /mnt;ls /mnt 可以看到下面有如下两个文件VMwareTools-6.0.0-45731.i386.rpm VMwareTools-6.0.0-45731.tar.gz
安装VMwareTools 采用rpm包安装：
rpm -ivh VMwareTools-6.0.0-45731.i386.rpm
vmware-config-tools.pl
一路回车，完成后出现分辨率列表供选择
或者采用tar包安装：
cp VMwareTools-6.0.0-45731.tar.gz /tmp;
tar zxvf VMwareTools-6.0.0-45731.tar.gz;
cd VMwareTools-6.0.0-45731.tar.gz;
./vmware-install.pl
umount /dev/cdrom init 5 安装完成后，如有问题，可以通过执行/usr/bin/vmware-config-tools.pl 来运行vmware tools，重新配置vmware tool及设定系统分辨率等。
运行vmware tools后,X11的配置文件/etc/X11/xorg.conf内容为：
# Xorg configuration created by system-config-display
Section "ServerLayout"
Identifier "single head configuration"
Screen 0 "Screen0" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "XWorkAround"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
Option "XkbModel" "pc105"
Option "XkbLayout" "us"
EndSection
Section "Device"
Identifier "VMware SVGA"
Driver "vmware"
EndSection
Section "Screen"
Identifier "Screen0"
Device "VMware SVGA"
Monitor "vmware"
# Don't specify DefaultColorDepth unless you know what you're
# doing. It will override the driver's preferences which can
# cause the X server not to run if the host doesn't support the
# depth.
Subsection "Display"
# VGA mode: better left untouched
Depth 4
Modes "640x480"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 8
Modes "1024x768"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 15
Modes "1024x768"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 16
Modes "1024x768"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 24
Modes "1024x768"
ViewPort 0 0
EndSubsection
EndSection
Section "Monitor"
Identifier "vmware"
VendorName "VMware, Inc"
HorizSync 1-10000
VertRefresh 1-10000
EndSection
Section "InputDevice"
Identifier "XWorkAround"
Driver "void"
EndSection3、Bridge模式下vmnet0问题采用VMWare安装Rehat AS 5时候，采用Bridge模式，启动时候报错：
The network bridge on device VMnet0 is not running. The virtualmachine will not be able to communicate with the host or with othermachines on your network. Virtual device Ethernet0 will startdisconnected
原因是在宿主机的本地连接里少了：VMware Bridge Protocol,在正常安装后会在本地网卡的连接属性里有这一项的。
解决方法如下：
1、禁用vmnet1（host-only模式）和vmnet8(nat模式)网卡
2、在服务中禁用VMware NAT Service
3、安装VMware Bridge Protocol
控制面板->网络连接->本地连接->属性->安装->（选中服务）添加->从磁盘安装->浏览->
VMware安装路径\VMware Workstation目录下选 netbridge.inf
然后重装电脑。
4、VMware Tools在xeno服务器安装问题在DELL Powerdege 1900 服务器（xeon Processor）上安装的虚拟机，运行/usr/bin/vmware-config-tools.pl时候报错：
[root@linux-server-v1 ~]# vmware-config-tools.pl
It looks like you are trying to run this program in a remote session. This
program will temporarily shut down your network connection, so you should only
run it from a local console session. Are you SURE you want to continue?
[no] yes
Stopping VMware Tools services in the virtual machine:
Guest operating system daemon: [ OK ]
Trying to find a suitable vmmemctl module for your running kernel.
None of the pre-built vmmemctl modules for VMware Tools is suitable for your
running kernel. Do you want this program to try to build the vmmemctl module
for your system (you need to have a C compiler installed on your system)?
[yes]
Using compiler "/usr/bin/gcc". Use environment variable CC to override.
What is the location of the directory of C header files that match your running
kernel? [/usr/src/linux/include]
The path "/usr/src/linux/include" is not an existing directory.
找不到kernel的header文件，主要原因是没有安装kernel-xen-devel-2.6.18-8.el5，解决方案
确认安装了如下几个包，如果没有安装，从安装盘上拷贝安装上：
kernel-xen-2.6.18-8.el5
kernel-devel-2.6.18-8.el5
kernel-headers-2.6.18-8.el5
kernel-xen-devel-2.6.18-8.el5
相似回答
